珠三角地区大气PM_(2.5)理化特性季节规律与成因

基于珠三角大气超级站2013年8月至2014年3月PM2.5、PM2.5中主要水溶性无机离子组分及其重要气态前体物等参数的逐时在线监测结果,揭示当地大气PM2.5中二次无机组分与其气态前体物的相互作用,以及PM2.5理化特性与成因的季节差异。结果表明,观测期间,PM2.5、PM10的年平均质量浓度分别为64.2、105.1μg/m3,PM2.5在PM10中所占比例(PM2.5/PM10)平均为61.1%。SO2-4、NO-3、NH+4的年平均质量浓度分别为16.6、9.0、10.2μg/m3,3者之和(SNA)占PM2.5的比例(SNA/PM2.5)平均为55.8%,体现了二次转化对珠三角地区PM2.5污染的重要影响;不同季节,SNA/PM2.5为46.0%~64.3%,夏季最低,冬季最高,其中SO2-4、NH+4对PM2.5的贡献相对稳定,NO-3贡献的季节差异较大;秋、冬季各项观测参数浓度的日变化规律相对明显,夏季除HNO3和NH3外,多项观测参数在低浓度水平波动,日变化规律不明显;珠三角大气中具有足量气态NH3以中和硫酸盐和硝酸盐,PM2.5中NH+4、SO2-4、NO-3主要以(NH4)2SO4和NH4NO3形式存在;本研究站点夏季的硫氧化率和氮氧化率均高于广州市,这充分体现了该站点的区域性特征。     

不同混凝剂处理松花江低温水

东北松花江地区冬季有将近6个月的冰封期,低温季节水源水处理难度大。为了保证东北地区冬季饮用水供应,研究几种混凝剂在处理冬季松花江低温水时的混凝效果。实验结果表明,NPAC1和NPAC2水解产物中具有较高的Alb和Alc成分,拥有较高的电中和、吸附和网捕卷扫性能,高效聚铝铁(PAF)水解产物Fe(OH)3具有比表面积大、吸附架桥作用较强的优点。这3种混凝剂无论是在控制出水浊度还是在对水体有机物去除能力方面均优于目前水厂所使用的PAC和聚合氯化铝铁(水厂PAF);NPAC2的投加量达到50 mg/L时,出水浊度达到最优;当混凝剂投加量达到50 mg/L时,NPAC1的浊度去除率逐渐超过NPAC2,剩余浊度低于3.0 NTU;NPAC1、NPAC2和PAF 3种混凝剂对有机物的去除能力大致相当,当混凝剂投加量为50 mg/L时,这3种混凝剂处理后的水的UV254的值均低于0.06,而水厂使用的2种混凝剂处理后的水的UV254仍高于0.1;结合其对浊度去除的情况,可以判断55 mg/L的投药量为NPAC1的最优投药点,PAF的最佳投药量为65 mg/L;投加适量的粉末活性碳可以有效地提高氨氮的去除率,当粉末活性炭的投加量为30 mg/L时,氨氮的去除率基本达到最大(51.27%)。表面负荷对混凝效果具有重要的影响,合理降低沉淀池的表面负荷对于提高出水水质具有重要作用。     

山东省主要河流中抗生素污染组成及空间分布特征

采用固相萃取-液相色谱/串联质谱法研究了山东省境内四大流域主要河流中抗生素污染组成及空间分布特征,涉及我国用量最大的6类共20种抗生素。结果表明:20种抗生素均有检出,且大环内酯类、喹诺酮类和四环素类抗生素整体检出浓度较高。就流域而言,半岛诸河流域抗生素污染较小,平均总质量浓度61.4 ng/L;海河流域、小清河流域和淮河流域相对较为严重,平均总质量浓度分别为232、175、118 ng/L。抗生素空间分布呈现一定的规律,检出浓度较高的点位主要集中在人口密集区下游,抗生素污染与周边生活污水、养殖企业废水和城市污水处理厂排水密切相关,而且抗生素组成可从一定程度上反映出污染来源。     

Identifying resource and environmental carrying capacity in the Yangtze River Economic Belt,China: the perspectives of spatial differences and sustainable development

Environment, Development and Sustainability - The resource and environmental carrying capacity (RECC) is an important foundation and support for a city or region, and determines the direction of...     

基于环境一号卫星的PM2.5浓度遥感反演研究

2014年12月29—30日,青岛市发生了一次空气污染过程,利用环境一号卫星CCD遥感影像数据和实测PM_(2.5)浓度数据,分析了该过程前后5 d的实测PM_(2.5)浓度与环境一号卫星CCD遥感影像的DN值之间的相关性,分别按日期和区域建立了反演模型。结果表明,按日期拟合反演模型相关系数为0.02~0.51,按区域拟合反演模型相关系数为0.01~0.80,总体来说,区域拟合结果较好。     

Effect of composite amendments on physicochemical properties of copper tailings repaired by herbaceous plants

Environmental Science and Pollution Research - Phytoremediation is considered to be the most environmentally friendly green restoration technology for dealing with mine waste. Adding amendments can...     

Classification and comparison of municipal solid waste based on thermochemical characteristics

Municipal solid waste (MSW) has been normally sorted into six categories, namely, food residue, wood waste, paper, textiles, plastics, and rubber. In each category, materials could be classified further into subgroups. Based on proximate and ultimate analysis and heating value, statistical methods such as analysis of variance (ANOVA) and cluster analysis were applied to analyze the characteristics of MSW in every subgroup and to try to distinguish their relative properties. The chemical characteristics analysis of MSW showed that polyethylene (PE), polypropylene (PP), and polystyrene (PS) had the highest volatile matter content, with almost no ash and fixed carbon, while polyethylene terephthalate (PET) had high carbon content but low hydrogen content. Bones and vegetables had the highest ash content, while nutshells and rubber had the highest fixed carbon content. Paper and starch food had the highest oxygen content, and wool and bones had the highest nitrogen and sulfur content. Polyvinyl chloride (PVC) had the highest chlorine content at about 55%. PE, PP, and PS had the highest heating value, followed by chemical products such as rubber and chemical fiber. Conversely, paper, vegetables and bones had the lowest heating value. The results of cluster analysis of MSW components showed that fruit peel, weeds, wood, bamboo, leaves and nutshells could be classified as the lignocellulose category; starch food, cotton, toilet paper, printing paper and cardboard could be classified as the glucose monomer category; wood and chemical fiber could be classified as the high nitrogen and sulfur category; and PE, PP, and PS could be cluster as the polyolefin category.

Implications: The yield of municipal solid waste (MSW) is constantly increasing and waste to energy (WTE) has been used extensively all over the world. During the processes of incineration, pyrolysis, or gasification, the impact of physical and chemical properties of MSW is of great significance. However, the traditional classification of MSW is too general to provide more detailed information in many investigations. It is necessary to perform the investigation of characteristics of combustible MSW to distinguish different categories of MSW and find out their subclassification.